HOOD & COMPONENTS. #1. #2. #3. Body side. Bumper cover. Fender. Hood side. Radiator support.. 2021 Lexus RX350L 3.5L V6 A/T AWD

Front. Hood.

Front. Hood plug. A device that is installed in the Hood that when removed allows any water to be removed from being inside the Hood panel. Material to provide protection from paint. Multi-Purpose Tape. Part cannot be reused/reinstalled. Seal used for the Hood. Side Body Trim Protector.

bumper cover. Front. Hood bumper. Left.fender. Right.fender. A clip which helps secure the Hood Hinge Cover to it's mounting point. Bumper Cover Support Rail Insulator. Rubber Cushion used to Support and prevent the Hood from rattling. Included with: Corner shield, Upper Support.

Front. Hood bumper. radiator support.

Front seal.

Front seal retainer. Clip that fastens hood Seal to hood. Fender Closing Plate Clip. Radiator Support Access Cover Clip. Fender Closing Plate. Outer. Radiator Support Access Cover. Side. Sight shield fastener. To hood retainer. W'strip. Included with: Closing Plate, Front Seal, Front Seal Part cannot be reused/reinstalled, Front weatherstrip, Front weatherstrip Part cannot be reused/reinstalled, Seal, Seal strip, Seal to hood, Seal to Radiator Support, Seal to upper tie bar, Side Seal, Sight shield.

Front. Insulator.

Insulator clip. Clip that fastens hood seal to hood. Dashboard Panel Insulator Clip. Fender Clip. Hood Insulation Pad Clip. Part cannot be reused/reinstalled. Dashboard Panel. Fastener. Fender. Hood Insulation Pad. Protector. Retainer. Seal. Included with: Front seal, Insulator.

Front Left. Hinge. Left.

Front Right. Hinge. Right.

Hinge bolt. Left. Right.

Front. Lock.

Lock cover.

Lock cover clip. A Clip which helps secure the Backup Warning System Control Module to it's mounting point. A Clip which helps secure the Hood Latch Support to it's mounting point. A Clip which helps secure the HVAC Electronic Control Module to it's mounting point. A securing fastener which pushes in or snaps into place to secure the Hybrid Battery Compartment Cooling Fan Duct. A securing fastener which pushes in or snaps into place to secure the Hybrid High Voltage Battery Cover. Bumper Impact Absorber Clip. Clip that fastens radiator Support or radiator baffle. Clip that locks the base into place and secures it from moving around in it's mounting surface. Dashboard Panel Insulator Clip. Deck Lid Trim Clip. Engine Air Intake Hose Clip. Fastens fender liner to vehicle. Fender Flare Clip. Hardware used to attach Bumper Cover to the vehicle. Hood Latch Striker Plate Clip. Mud Guard Clip. Package Tray Trim Clip. Part cannot be reused/reinstalled. Partition Panel Clip. Quarter Panel Splash Shield Clip. Quarter Panel Trim Panel Clip. Radiator Support Access Cover Clip. Radiator Support Air Deflector Clip. Radiator Support Splash Shield Clip. Rear Body Panel Trim Panel Clip. Secures the windShield washer fluid reservoir filler tube to the vehicle. Trunk Trim Panel Clip. Wheel Arch Molding Clip. Included with: Cover assembly, Fender liner assembly, Insulating Cover, Washer reservoir, Wheel opening Molding.

Front. Release cable.

#1. PartQualifier: #1. Release cable clip. A bracket for a antenna. A part which fits around the Hood Release Cable and tightens, thereby securing the component in place with a Clamping force. Deck Lid Release Cable Clip. Fuel Filler Door Release Cable Clip. Hood Release Cable Clip. Part is included in Antenna assembly. holder. retainer. Antenna, manual bracket. Deck Lid. Fuel Filler Door. Hood. Lock.

#3. PartQualifier: #3. Release cable clip. A part which fits around the Hood Release Cable and tightens, thereby securing the component in place with a clamping force. Hood Release Cable Clip. WIRING HARNES. Washer hose.

Front. Linkage shield.

black. Front. Release lever.

Left. Right.

Front Right Lower. Lift cylinder bracket. PartQualifier: body side. Right.body side.

Front Left Lower. Left.body side. Lift cylinder bracket. PartQualifier: body side.

Lift cylinder bracket. PartQualifier: hood side. Right.hood side. Bracket used to secure the Hood Lift Support. Hood Lift Support Stud. Rod. Stay. Strut. Stud.

Left.hood side. Lift cylinder bracket. PartQualifier: hood side. Bracket used to secure the Hood Lift Support. Hood Lift Support Stud. Stay,. Rod. Strut. Stud.

#2. PartQualifier: #2. Release cable clip.